Paint for Roads, Construction & Civil Contractors

Road and civil contractors buy paint for three jobs: marking roads, priming steel on site, and painting galvanised roofing. Marindec manufactures road marking paint to SANS 731-1, and the primers and enamels for the steel, in Alrode, Alberton.

This page covers each job, with figures from our technical data sheets (TDS).

Coating systems for site work

JobCoating systemFrom the data sheet
Lane lines, pedestrian crossings, stop lines, road symbolsRoad marking paint to SANS 731-1150 µm dry film thickness (DFT) on a new road, 75 µm when re-marking; hard dry in 45 minutes
Structural steel, gates and fencing (mild steel)ZPPW15 primer + Fast Dry Enamel or AGRIP30+Primer 20–35 µm DFT; next coat within 2 hours
Exposed steel needing a UV-stable finishTwo-pack (2K) high-build primer, ask us + 2K polyurethane35–45 µm DFT; full cure about 7 days
IBR roofing, galvanised cladding and fencingGalvanised Iron Primer + topcoat50–60 µm DFT; overcoat after overnight drying
Aluminium and non-ferrous partsEPS15 etch primer + topcoat10–15 µm DFT; overcoat after at least 1 hour
Cleaning steel before paintingArmourphos CleanerPaint only on dry steel at least 3 °C above the dew point

Road marking paint to SANS 731-1

Marindec's Fast Drying Road Marking paint is a solvent-based modified alkyd made to SANS 731-1. The data sheet rates it for bituminous roads, and the catalogue lists it for asphalt and concrete road surfaces.

It is used for traffic lane lines, pedestrian crossings, stop lines and road symbols, by road construction contractors, civil engineering firms and municipalities. White and yellow are listed in 5L tins, and we also supply 200L drums.

We make solvent-based road marking paint only. If a specification calls for a water-based marking paint, tell us before you order.

Road marking paint specification

PropertyData sheet figure
StandardSANS 731-1
BinderModified alkyd, suitable for bituminous roads
Dry film thickness (DFT)150 µm on a new road; 75 µm when re-marking
Coverage4–5 m² per litre at 150 µm DFT
SolidsAbout 46% by volume
No-pick-up timeUnder 15 minutes
Hard dry45 minutes
ApplicationBrush, roller or spray

The data sheet gives drying times without a stated temperature or humidity. Cold or damp weather slows drying, so if a specification sets a faster hard dry, send it to us first.

To check a tender or municipal specification against these figures line by line, see how to check a road marking specification.

Road marking paint coverage

At 150 µm, one litre covers 4 to 5 m² in theory, so a 5L tin covers about 20 to 25 m². On a 100 mm line, that is roughly 200 to 250 metres per tin.

Re-marking at 75 µm uses about half as much paint per metre. Rough or open-textured surfaces and spray losses cut real coverage, so order extra.

Applying road marking paint

  • The surface must be clean, dry and free from gravel.
  • Apply by brush, roller or spray to the full film thickness. A thin line wears out early.
  • Keep traffic off until the paint is past its no-pick-up time, and ideally until it is hard dry at 45 minutes.

The SANS 731-1 road marking guide covers types, application and drying in more detail.

Primers for site steel

Structural steel, steel gates and perimeter fencing take a primer from the FPW15 family before topcoating. These are fast-drying alkyd primers, often specified in tenders as red oxide primer.

Outdoors, use ZPPW15, the grade with a zinc-modified phosphate anti-corrosive additive. It goes on at 20 to 35 µm DFT, is touch dry in about 10 minutes and takes the topcoat within 2 hours.

Galvanised steel and aluminium need their own primers. Use Galvanised Iron Primer on zinc-coated steel, and EPS15 etch primer at 10 to 15 µm DFT on aluminium and other non-ferrous metals.

Prime blasted steel the same day, before flash rust forms, and stripe-coat welds and bolts first. See steel surface preparation and the film thickness guide.

Fabricated steel often arrives on site already primed. For shop priming and full systems, see steel fabrication and structural steel.

IBR roof paint and galvanised site buildings

IBR (inverted box rib) roof sheeting is galvanised, and red oxide or FPW15 primers don't hold on zinc. Prime it with Galvanised Iron Primer, made for galvanised iron, zinc-coated steel and pre-galvanised sheeting.

Wash new sheeting with galvanised iron cleaner or sugar soap, rinse and let it dry. New sheeting gets a full primer coat; on a painted roof, spot-prime only the bare metal.

Galvanised Iron Primer goes on at 50 to 60 µm DFT, is touch dry in about 2 hours and takes its topcoat the next day. The IBR sheeting guide covers the topcoat and the order of work.

Supply for contractors

Marindec manufactures in Alrode, Alberton (Gauteng), for collection or delivery nationwide, with regular supply to Gauteng, Mpumalanga and the Western Cape. Road marking paint comes in 5L tins and 200L drums for contract volumes.

See delivery and supply areas and bulk paint supply. For floor demarcation in warehouses, see warehouses and logistics.

Request a quote with the job, the specification and the volume. Quotes usually come back the same working day.