| SKU | 43-9561-005 |
|---|---|
| Pack sizes | 5L |
| System role | marking |
| Finish | gloss |
| Substrates | concrete, previously painted |
| Environments | interior, industrial |
| Dry time | touch ± 45 to 60 minutes (depending on applied WFT) · hard ± 4 to 8 hours (depending on applied WFT) |
| Coverage | 7.5 m²/litre @ 45 µm DFT theoretical; practical 50 to 70% less |
| Volume solids | ± 36% (depending on colour) |
Floor Marking — Redox 130 5L
This floor marking product provides exceptional durability and visibility, enhancing safety and organization in construction, warehousing, and manufacturing. It resists wear, UV exposure, and corrosion for long-lasting performance.
Use cases
- Single-pack, medium hi-build floor and stoep enamel for floors, walkways and line marking. Apply by brush, roller (small areas) or air spray; thin up to 10–15% with GP/QD thinner. Touch dry in about 45–60 minutes, hard dry in 4–8 hours, recoat within 3–4 hours.
Technical data
From the Marindec technical data sheet for Floor / Stoep Enamel (43 series), TDS 1/170429. Drying and overcoating times vary with ambient temperature.
| Type | Medium hi-build, medium drying, single pack gloss enamel |
|---|---|
| Recommended film thickness | 35 to 50 µm DFT (100 to 140 µm WFT) |
| Theoretical spread rate | 7.5 m²/litre @ 45 µm DFT |
| Practical spread rate | 50 to 70% less than theoretical, depending on substrate & application conditions |
| Solids by volume | ± 36% (depending on colour) |
| Touch dry @ 23 °C | ± 45 to 60 minutes (depending on applied WFT) |
| Hard dry @ 23 °C | ± 4 to 8 hours (depending on applied WFT) |
| Overcoating interval | Within 3 to 4 hours |
| Recommended thinner | GP/QD Thinner for viscosity adjustment and for cleaning |
| Application |
|
| Substrate conditions | Dry and free of any dirt, dust or oily residues; at least 3 °C above dew point; clean sufficiently by sandblasting or with sandpaper |
Datasheets
Frequently asked questions
What is Floor Marking — Redox 130 5L used for?
Single-pack, medium hi-build floor and stoep enamel for floors, walkways and line marking. Apply by brush, roller (small areas) or air spray; thin up to 10–15% with GP/QD thinner. Touch dry in about 45–60 minutes, hard dry in 4–8 hours, recoat within 3–4 hours.
Which surfaces can Floor Marking — Redox 130 5L be applied to?
Suitable substrates include concrete, previously painted.
Does Floor Marking — Redox 130 5L need a primer?
No — it can be applied direct to a properly prepared substrate.
What thinner should I use with Floor Marking — Redox 130 5L?
Per the Marindec technical data sheet: GP/QD Thinner for viscosity adjustment and for cleaning.
What film thickness should Floor Marking — Redox 130 5L be applied at?
The technical data sheet recommends 35 to 50 µm DFT (100 to 140 µm WFT).
What should I know before applying Floor Marking — Redox 130 5L?
Floor/Stoep Enamel, 43 series. Applied mostly on concrete floors, usually without a primer once the floor has been cleaned thoroughly. The data sheet gives its principal use as steel products; the same product is sold as Transport Enamel.
How quickly does Floor Marking — Redox 130 5L dry?
Per the Marindec technical data sheet: touch dry ± 45 to 60 minutes (depending on applied WFT) and hard dry ± 4 to 8 hours (depending on applied WFT) at 23 °C. Drying times vary with temperature and film thickness.
What coverage does Floor Marking — Redox 130 5L give?
The Marindec technical data sheet gives a theoretical spread rate of 7.5 m²/litre @ 45 µm DFT. Practical spread is 50 to 70% less than theoretical, depending on substrate & application conditions.
What pack sizes are available?
Floor Marking — Redox 130 5L is supplied in 5L.