| SKU | 43-955-005 |
|---|---|
| Pack sizes | 5L |
| System role | marking |
| Finish | gloss |
| Substrates | concrete, previously painted |
| Environments | interior, industrial |
| Dry time | touch ± 45 to 60 minutes (depending on applied WFT) · hard ± 4 to 8 hours (depending on applied WFT) |
| Coverage | 7.5 m²/litre @ 45 µm DFT theoretical; practical 50 to 70% less |
| Volume solids | ± 36% (depending on colour) |
Floor Marking — Green IG237 5L
This floor marking product delivers durable, vibrant markings resistant to heavy traffic, UV fading, and corrosion, ensuring safety and organization in industrial settings with quick application.
Use cases
- Single-pack, medium hi-build floor and stoep enamel for floors, walkways and line marking. Apply by brush, roller (small areas) or air spray; thin up to 10–15% with GP/QD thinner. Touch dry in about 45–60 minutes, hard dry in 4–8 hours, recoat within 3–4 hours.
Technical data
From the Marindec technical data sheet for Floor / Stoep Enamel (43 series), TDS 1/170429. Drying and overcoating times vary with ambient temperature.
| Type | Medium hi-build, medium drying, single pack gloss enamel |
|---|---|
| Recommended film thickness | 35 to 50 µm DFT (100 to 140 µm WFT) |
| Theoretical spread rate | 7.5 m²/litre @ 45 µm DFT |
| Practical spread rate | 50 to 70% less than theoretical, depending on substrate & application conditions |
| Solids by volume | ± 36% (depending on colour) |
| Touch dry @ 23 °C | ± 45 to 60 minutes (depending on applied WFT) |
| Hard dry @ 23 °C | ± 4 to 8 hours (depending on applied WFT) |
| Overcoating interval | Within 3 to 4 hours |
| Recommended thinner | GP/QD Thinner for viscosity adjustment and for cleaning |
| Application |
|
| Substrate conditions | Dry and free of any dirt, dust or oily residues; at least 3 °C above dew point; clean sufficiently by sandblasting or with sandpaper |
Datasheets
Frequently asked questions
What is Floor Marking — Green IG237 5L used for?
Single-pack, medium hi-build floor and stoep enamel for floors, walkways and line marking. Apply by brush, roller (small areas) or air spray; thin up to 10–15% with GP/QD thinner. Touch dry in about 45–60 minutes, hard dry in 4–8 hours, recoat within 3–4 hours.
Which surfaces can Floor Marking — Green IG237 5L be applied to?
Suitable substrates include concrete, previously painted.
Does Floor Marking — Green IG237 5L need a primer?
No — it can be applied direct to a properly prepared substrate.
What thinner should I use with Floor Marking — Green IG237 5L?
Per the Marindec technical data sheet: GP/QD Thinner for viscosity adjustment and for cleaning.
What film thickness should Floor Marking — Green IG237 5L be applied at?
The technical data sheet recommends 35 to 50 µm DFT (100 to 140 µm WFT).
What should I know before applying Floor Marking — Green IG237 5L?
Floor/Stoep Enamel, 43 series. Applied mostly on concrete floors, usually without a primer once the floor has been cleaned thoroughly. The data sheet gives its principal use as steel products; the same product is sold as Transport Enamel.
How quickly does Floor Marking — Green IG237 5L dry?
Per the Marindec technical data sheet: touch dry ± 45 to 60 minutes (depending on applied WFT) and hard dry ± 4 to 8 hours (depending on applied WFT) at 23 °C. Drying times vary with temperature and film thickness.
What coverage does Floor Marking — Green IG237 5L give?
The Marindec technical data sheet gives a theoretical spread rate of 7.5 m²/litre @ 45 µm DFT. Practical spread is 50 to 70% less than theoretical, depending on substrate & application conditions.
What pack sizes are available?
Floor Marking — Green IG237 5L is supplied in 5L.